S Series – 30” DIAMETER ROTOR
- Threshes well, reduces rumbling, and improves sample
- Similar bar design as the R and N series Precision rotor
N & R Series – 25” DIAMETER ROTOR
- Completely enclosed – no dirt build up
- High inertia, dynamically balanced – no vibration
- Progressive 4×7 pattern uses fewer bars – less stem damage and less chaffer loading
- Threshes quicker, separates sooner, reduces rotor loss
- Handles weeds and straw bunches with ease
- Wider cylinder to concave clearances possible
- Rotor speeds may be reduced in some conditions
- Reduces strain on gear box, rotor belt, main clutchshaft, and separator clutch
- Allows chipping the engine (L-10 & M-11 engines) without damage to threshing drive components
- Bars available: heat treated, chrome plated, or chrome alloy
L, N, R, & S series – FINE CUT CHOPPER
- 20 heavy duty, heat treated, double edged knives
- Balanced for high speeds
- Cuts finer and discharges material better at high speeds (2900+ rpm)
- Works well with speed-up kit
- Small center drum handles large volumes of straw well
S series – CHOPPER SPEED-UP KIT
- Includes large double B pulley, 1-1/4 bushing, and 5″ idler pulley
R series – CHOPPER SPEED-UP KIT
- Includes single groove pulley, hub, and Kevlar cord belt
- Use OEM step pulley for corn
R & S series – STRAW CHOPPER FLOOR (AR PLATE)
- Flattened floor improves straw flow for better discharge
- Hits chopper at a lower angle
R70 series – SECTIONAL CONCAVE
- Has 3 removeable full length sections, mount side by side in original style frame
- Four sections used in 30″ diameter concave available for Super Series Combines
- Available in heat treated and chromed
- Special wire spacing prevents plugging, even in high moisture corn
- First 4 spaces have extra narrow wire spacing, eliminating the need for filler plates and eliminating white caps in hard to thresh grains
- Threshing and separating starts immediately, reducing grain damage and rotor loss
- Short wires may be removed for corn and beans
P3 series – FILLER PLATES
- Intended for OEM concave
- Very easy to install and remove
- Covers 2 spaces and held in place with two ‘J’ hooks
- In hard to thresh grain, covering 6 spaces is recommended
L & M series – 4×4 HI INERTIA CYLINDER
- Has 4 bars around the circumference, and four columns from left to right
- Can increase concave to cylinder clearance and slow RPM’s to reduce seed damage
- Effective in soybeans
- Allows large amounts of straw in between bars
- Plugging rarely occurs, and in tough conditions combine capacity will be more than doubled
L & M series – BEATER SPEED-UP KIT
- Includes double groove cylinder pulley, hub, speed sensor disc, and two drive belts
- Increases speed of rear beater to take material away from cylinder fast enough to eliminate slugging
- Works on chain drive cylinders with a 24T sprocket on the cylinder, driving an 18T sprocket on the beater
P3 series – CHAFF FINS
- 2 lefts and 2 rights, mount on chaff board
- Spreads chaff over 30′ in calm conditions
- Works in canola and light seeds with board in the down position
N, R, & S series – FEED ACCELERATOR LUGS
- Polyurethane composition, last 2 1/2 to 3 times longer than OEM lugs
N, R, & P3 series – CHROMED PIN FEEDER CHAINS
- Aggressive polyurethane slats reduce slat bending and breakage
- Lighter than OEM chains, extends chain and sprocket life
- Available in 3 strand and 4 strand design
L, M, & P3 series – FEEDER CHAIN SPROCKETS
- High quality split steel sprockets are very precise
- Available in 1-1/2″ and 1-13/4″ hex bore
- Easy to reverse
N & R series – FEEDER HOUSE FLOOR LOWERING KIT
- Lowers rear of front floor and front of rear floor, and flattens rear floor depression
- Recommended when feeding problems are encountered in tough conditions
P3 series – FRONT FEEDER FLOOR WEAR PLATE (AR PLATE)
- Heavy duty construction for longer wear
R & S series – HEAVY DUTY STOP SIGN
- 1/4″ plate stops the bending of the rotor support plate encountered in certain tough conditions
R & S series – POSI-FEED ROLLER
- Triangular shaped feeder drum, has more capacity to move material
- Floor lowering kit may not be required when installed in rear chain position
- Can lock rear drum in corn position for maximum feed
N, R, & S series – SMALL SEEDS CHAFFER BOARD
- Mounts on rear of chaffer
- Available in two lengths: 53 3/8″ and 60 3/16″
- Allows greater wind speed without blowing grain out
- Particularly effective in canola, mustard, flax, and sunflowers, may be used in wheat too
POWER CHIP
- Effective on late model M-11 Cummins and some L-10 engines
- Increases capacity 10% – 30% and improves fuel economy
- Use only if combine is equipped with staggered bar rotors
- Gives the Super series machines a run for their money
UNLOAD AUGER EXTENSIONS
- 30″ x 12″ and 30″ x 14″ extensions available