John Deere

S series — Fan Support Bracket

  • Gives better air control on the JD ‘S’ series combine shoe
  • Fan brackets move the position of the separator fan. Making the wind settings easier to adjust.
  • Eliminates air flow dead spots in the chaffer

Price: $0.00

S series — Bottom Sieve Extension

  • Reduces the amount of return material
  • Matches the length of chaffer
  • Reduces overloading of the return
  • Non-adjustable, but dramatically reduces the amount of clean grain going back through the return

Price: $0.00

STS, 9600, 9500, & 8820 series — FEED ACCELERATOR/DISCHARGE BEATER

  • Totally enclosed design, eliminates cleanout between grain varieties
  • Staggered blades easily tear bunches apart and feed rotor uniformly
  • Takes less horsepower, extending pulley life, eliminating feeder chain stress and burned or broken drive belts
  • Dynamically balanced, eliminates vibration
  • Comes with 4-way reversible blades

Price: $0.00

STS series — Variable Stream Bars

  • High capacity threshing bars for S-670, S-680, S-690
  • Greatly improves samples in hard to thresh grains
  • Improves ground speed up to 2 mph
  • Reduces amount of tailing’s
  • Reduced cylinder speeds are common, requiring less horsepower and increased fuel economy
  • Reduced white caps when used with Precision Farm Parts concave which does not need filler plates

Price: $0.00

STS series — DISCHARGE BEATER SPEED-UP KIT

  • Includes heavy duty pulley and Kevlar cord belt
  • Allows for almost instantaneous recovery of engine speed following reduction in RPMs
  • Improves transfer of material from the cylinder to straw walkers without slugging
  • Reduces straw breakage, walker loss, and chafer loading
  • Can be installed in 20-30 minutes

Price: $0.00

9500 & 9600 series — BEATER SPEED-UP KIT

  • Improves transfer of material from the cylinder to straw walkers without slugging
  • Reduces straw breakage, walker loss, and chaffer loading

Price: $0.00

8820 series — BEATER SPEED-UP KIT

  • Optimizes straw flow with the use of a smaller pulley for the beater

Price: $0.00

STS series — LI’L BRUTE CONCAVES

  • Heavy duty half-size concave – takes 6 to replace 3 OEM concaves
  • Concaves match JD concaves so 2 may be purchased to replace one OEM concave at a time
  • Lightweight (65#) and sturdy, will maintain shape
  • Bolt-on front feed lip – can switch concaves to extend wear
  • 1/4″ wires allows for extended wear
  • Wire spacing available in four widths: extra narrow, narrow, wide, and corn
  • Use extra narrow concaves to control white caps, and use narrow, wide, and corn concaves for all other applications
  • Reduces the need for cover plates, increasing capacity and reducing rotor loss

Price: $0.00

STS series — REMOVABLE FEED LIP

  • Removable feed lip allows Li’l Brute concaves to be configured to harvesting conditions
  • Bolts on, allowing feed lip to be moved from one concave to another

Price: $0.00

STS series — WHITE CAP KIT

  • Plugs the crack on right hand side of the rotor where concaves meet the cage
  • Keeps whole and partial heads from passing through before being threshed

Price: $0.00

STS series — THRESHING ELEMENTS (Set of 9)

  • Staggered design removes the three walls of bars resulting in less slugging in tough or bunched conditions
  • Reduces groaning in tough or weedy conditions
  • Rasp bars thresh grain better, and move material easier and faster, allowing greater concave to rotor clearance even in the toughest conditions
  • Greater concave to rotor clearance means better wear of the concaves and rasp bars
  • Allows for increased ground speeds, 10% or better fuel economy improvement
  • Reduces dockage (.5 -1.5% average dockage)

Price: $0.00

9600 & 8820 series — 4×6 CYLINDER

  • Has 4 bars on the circumference and 6 columns from left to right (24 bars)
  • Totally enclosed, no dirt build-up
  • Dynamically balanced, no vibration
  • Staggered design rarely plugs and allows for constant cylinder speed, uniform feeding, better threshing, and less slugging in bunched conditions
  • Allows for increased concave to cylinder clearances
  • Reduced cylinder speeds are common, requiring less horsepower and increased fuel economy
  • Capacity increases of 30% or more are common depending on crop and crop conditions

Price: $0.00

9600 series — 6×6 CYLINDER

  • Has 6 bars on the circumference and 6 columns from left to right (36 bars)
  • Totally enclosed, no dirt build-up
  • Dynamically balanced, no vibration
  • Staggered design rarely plugs and allows for constant cylinder speed, uniform feeding, better threshing, and less slugging in bunched conditions
  • Allows for increased concave to cylinder clearances
  • Reduced cylinder speeds are common, requiring less horsepower and increased fuel economy
  • Capacity increases of 30% or more are common depending on crop and crop conditions

Price: $0.00

105, 4420, 6620, 7720, & 9500 series — 4×5 CYLINDER

  • Has 4 bars on the circumference and 5 columns from left to right (20 bars)
  • Totally enclosed, no dirt build-up
  • Dynamically balanced, no vibration
  • Staggered design rarely plugs and allows for constant cylinder speed, uniform feeding, better threshing, and less slugging in bunched conditions
  • Allows for increased concave to cylinder clearances
  • Reduced cylinder speeds are common, requiring less horsepower and increased fuel economy
  • Capacity increases of 30% or more are common depending on crop and crop conditions

Price: $0.00

9500 series — 6×5 CYLINDER

  • Has 6 bars on the circumference and 5 columns from left to right (30 bars)
  • Totally enclosed, no dirt build-up
  • Dynamically balanced, no vibration
  • Staggered design rarely plugs and allows for constant cylinder speed, uniform feeding, better threshing, and less slugging in bunched conditions
  • Allows for increased concave to cylinder clearances
  • Reduced cylinder speeds are common, requiring less horsepower and increased fuel economy
  • Capacity increases of 30% or more are common depending on crop and crop conditions

Price: $0.00

9500 & 9600 series — BEATER GRATE

  • Heavy duty round rod construction for extended life

Price: $0.00

8820, 9500, & 9600 series — CONCENTRIC CONCAVE

  • Concentric, line bored concave that fits the cylinder
  • Wide wire spacing maximizes grain separation
  • Wires extend all the way back, eliminating need for corn fillers in rear of concave
  • Optimum wire depth, results in reduced power requirements, and reduced stem breakage

Price: $0.00

9500 & 9600 series — PRETHRESHER FEED PLATE

  • Replaces original smooth feed plate
  • Reduces white caps in hard to thresh grains, yielding better samples with reduced dockage
  • Threshing and separation starts earlier, reducing walker loss
  • May be installed without removing feeder house
  • Usually eliminates need for filler plates

Price: $0.00

9500 & 9600 series — POSI-FEED ROLLER

  • Helps maintain a constant, uniform flow, and improves fuel economy

Price: $0.00

9500 & 9600 series — STRAW WALKER RISERS

  • Moves material faster, reducing straw mat and walker loss
  • Great for tough, damp straw conditions
  • 9000 series combines can accommodate 8 mid mount risers per walker

Price: $0.00

8820 series — WALKER RISERS

  • Moves straw faster, reducing walker loss

Price: $0.00

8820 series — POLY STRIPPER PLATE

  • Wears longer than rubber OEM plate, and reduces backfeeding around cylinder
  • Located between cylinder and beater

Price: $0.00

STS series — FEEDER CHAIN SPLIT SPROCKETS

  • Splits in two to eliminate the need to remove shaft while replacing sprockets
  • Speeds up replacement time
  • Sold in sets of 3

Price: $0.00

STRAW CHOPPER

  • MAV replacement straw chopper rotor

Price: $0.00